The DIY Tool Review
Guide
Tool reviewNailers & Fastening

The Best Brad Nailers for DIY (2026)

Six 18-gauge brad nailers, cordless and pneumatic, and the only question that actually separates them: what comes in the box. The WEN 20512 is the one we would buy.

Photo of Cheryl Thompson
Cheryl Thompson
Category
Nailers & Fastening
Tools tested
6
Read time
16 min
Updated
Six 18-gauge brad nailers on a workbench, four cordless with battery packs and two pneumatic, beside strips of collated brad nails
Six 18-gauge brad nailers on a workbench, four cordless with battery packs and two pneumatic, beside strips of collated brad nails ยท Photo ยท Cheryl Thompson

The best brad nailer for DIY, for most people, is the WEN 20512 at $108.00 as of November 2026. It arrives as a complete working tool โ€” 20V battery, charger and 400 brads in the box โ€” so there is nothing else to buy. Two guns here carry a lower sticker price, and both of them send you shopping again.

Those two are the whole story of this category. The CRAFTSMAN CMCN618B is $99.00 as of November 2026 with no battery and no charger. The WEN 61723K is $39.16 as of November 2026 and needs an air compressor you may not own. Neither stays cheap once you have finished buying it.

So this is not six versions of the same tool. It is six different deals, and the job below is to work out which one you are in. For the wider picture, start with our guide to the best nail gun for DIY โ€” a brad nailer is one of several nail gun types explained in there. If you do not yet own the basics, a nailer is not where to start: our essential DIY tools list comes first.

How we picked

We worked from what each tool's Amazon listing publishes, plus its price as of November 2026. We have not fired any of them; where a listing does not publish a figure, we say so rather than guess. Scope is 18-gauge brad nailers only โ€” 16-gauge finish nailers are a heavier tool for heavier stock.

Then price. The cheapest tool here is $39.16 and the dearest $279.00. Divide one by the other and the top of this category costs about 7.1 times the bottom, a spread of $239.84. Almost none of that gap is about how well a gun drives an 18-gauge brad. It is about what comes in the box and where the power comes from.

One honesty check first. If the job is a dozen brads into a picture frame, a hammer and a nail set will be done before a compressor finishes filling; our guide to claw hammers covers that end of the work. A nailer earns its keep when you drive brads by the hundred โ€” a room of baseboard, a run of shoe molding, a batch of cabinet backs. In the usual buying order it is a second-wave purchase, landing after the drill, impact driver and circular saw on our must-have cordless power tools list.

The best brad nailers for DIY at a glance

At a glance5 picks compared
01Best Overall
WEN 20V Max Cordless 18-Gauge Brad Nailer with 2.0Ah Battery and Charger (20512)

WEN 20512

Check price
02Best Bare Tool
CRAFTSMAN V20 Brad Nailer, 18GA, Cordless, Bare Tool Only (CMCN618B)

CRAFTSMAN CMCN618B

Check price
03Best Budget Pneumatic
WEN 18-Gauge 3/8-Inch to 2-Inch Pneumatic Brad Nailer Kit with Case and Nails (61723K)

WEN 61723K

Check price
04Best Pneumatic
DEWALT Brad Nailer Kit, 18GA, 5/8-Inch to 2-Inch, Pneumatic (DWFP12231)

DEWALT DWFP12231

Check price
05Best Published Runtime
Metabo HPT Brad Nailer, 18 Gauge Cordless, 18V Kit, NT1850DG

Metabo HPT NT1850DG

Check price

Drag to compare all 5 โ†’

The short version: buy the WEN 20512 if you want one box that works, the WEN 61723K if you own a compressor and want to spend the least, and the DEWALT DWFP12231 if you own a compressor and want the better-finished tool.

WEN 20512 โ€” best overall

Best OverallASIN B0CH3R5G59
WEN 20V Max Cordless 18-Gauge Brad Nailer with 2.0Ah Battery and Charger (20512)
WEN 20V Max Cordless 18-Gauge Brad Nailer with 2.0Ah Battery and Charger (20512)

WEN 20512

A complete cordless brad nailer โ€” 20V battery, charger and 400 brads in the box โ€” that drives 18-gauge brads from 3/4 to 2 inches.

Pros

  • Battery, charger and 400 brads included โ€” nothing else to buy
  • 100-nail magazine
  • LED indicator reports battery status, magazine fill and tool temperature
  • The cheaper of the two guns here that ship with a battery

Cons

  • Its Amazon listing does not publish a nails-per-charge figure
  • Minimum brad length is 3/4 in., so it skips the shortest brads

At $108.00 the WEN 20512 answers every question in a single purchase: its listing puts a 2.0Ah battery, a charger and 400 18-gauge brads in the box, so the sticker price is the price of a tool that works. Of the two cordless guns here that ship with a battery, it is the cheaper one โ€” the Metabo HPT NT1850DG is $169.00 as of November 2026.

The published specs are modest and clear: 18-gauge brads from 3/4 in. to 2 in., a 100-nail magazine, no compressor and no hose. An LED indicator reports battery status, magazine fill and tool temperature, which is more explanation than most brad nailers offer when they suddenly stop driving.

Its listing publishes no nails-per-charge figure, and we will not invent one โ€” if runtime is your deciding number, skip to the Metabo.

Trim gets cut before it gets fastened, so if a room of baseboard is why you are here, the saw matters as much as the gun โ€” see our best miter saws for DIY.

Who should look elsewhere: anyone needing brads shorter than 3/4 in. The cheap pneumatic below goes to 3/8 in.

CRAFTSMAN CMCN618B โ€” best bare tool

Best Bare ToolASIN B0BZQXGXDN
CRAFTSMAN V20 Brad Nailer, 18GA, Cordless, Bare Tool Only (CMCN618B)
CRAFTSMAN V20 Brad Nailer, 18GA, Cordless, Bare Tool Only (CMCN618B)

CRAFTSMAN CMCN618B

A bare-tool V20 brad nailer that only makes financial sense if you already own CRAFTSMAN batteries.

Pros

  • Lowest sticker price of the cordless guns here
  • CRAFTSMAN lists up to 420 nails per charge
  • Tool-free jam and stall settings
  • Belt hook, and no compressor, hose or gas cartridge

Cons

  • Bare tool โ€” no battery and no charger in the box
  • Its Amazon listing does not publish a nail-length range
  • The runtime claim carries a double asterisk with no stated test conditions

The CMCN618B has the lowest sticker price of the four cordless guns here, $99.00 as of November 2026 โ€” and it is a bare tool. No battery. No charger. Set it against the WEN 20512 at $108.00 and the gap is exactly nine dollars. Nine dollars is what WEN charges you for a 2.0Ah battery, a charger and 400 brads.

So the arithmetic runs one way only. If you already own CRAFTSMAN V20 batteries, this is a $99.00 nailer and a sensible buy. If you do not, it is $99.00 plus a battery plus a charger, which lands well above the $108.00 WEN that includes both โ€” the cheaper-looking tool is the more expensive purchase. Our guide to cordless tool batteries explains what that bundle is worth.

Buying a bare tool is a bet on a battery system, not on a nailer, so it is worth reading our take on the best cordless power tool brand for DIY first.

On runtime, CRAFTSMAN lists up to 420 nails per charge. Treat that as a listing claim, not a result: the figure carries a double asterisk and the listing states no test conditions โ€” no brad length, no battery size, no material. The same listing gives no nail-length range, so we cannot tell you the shortest or longest brad it takes. It does publish tool-free jam and stall settings and a belt hook.

WEN 61723K โ€” best budget pneumatic

Best Budget PneumaticASIN B09JV7977X
WEN 18-Gauge 3/8-Inch to 2-Inch Pneumatic Brad Nailer Kit with Case and Nails (61723K)
WEN 18-Gauge 3/8-Inch to 2-Inch Pneumatic Brad Nailer Kit with Case and Nails (61723K)

WEN 61723K

Under forty dollars with 2,000 brads and a carrying case, and it takes brads as short as 3/8 inch โ€” but you supply the air compressor.

Pros

  • 2,000 brads in four lengths plus a carrying case included
  • Takes 3/8 in. brads โ€” shorter than either cordless gun here that publishes a minimum
  • 106-nail quick-release magazine
  • Depth adjustment wheel, nail gauge, rotatable exhaust and nose latch for jams

Cons

  • Requires a separate air compressor, which is not included
  • A hose tethers you to the compressor

$39.16 as of November 2026 makes this the cheapest tool in the guide and not the cheapest setup, because it is pneumatic and the compressor is not included. Hold both facts together every time that price appears.

What you get is otherwise generous: 2,000 18-gauge brads โ€” 500 each of 3/8 in., 3/4 in., 1 in. and 2 in. โ€” plus a carrying case. It runs on 60 to 115 PSI through a 1/4 in. NPT inlet, holds 106 nails in a quick-release magazine, and has a depth wheel, a nail gauge, a rotatable exhaust and a nose latch for jams.

Here is the part worth noticing. This $39.16 gun accepts 3/8 in. brads โ€” shorter than either cordless gun here that publishes a minimum. The WEN 20512 starts at 3/4 in. and the Metabo NT1850DG at 5/8 in. (The CRAFTSMAN and Milwaukee listings publish no nail-length range at all, so the comparison runs only across the three that do.) Short brads are what thin trim and small craft work need, so at that end of the range the budget gun is genuinely the more capable one.

DEWALT DWFP12231 โ€” best pneumatic

Best PneumaticASIN B00AK4CY7S
DEWALT Brad Nailer Kit, 18GA, 5/8-Inch to 2-Inch, Pneumatic (DWFP12231)
DEWALT Brad Nailer Kit, 18GA, 5/8-Inch to 2-Inch, Pneumatic (DWFP12231)

DEWALT DWFP12231

The better-finished pneumatic for someone who already runs a compressor: tool-free depth with detents, a stowable non-marring tip and a sequential-style trigger.

Pros

  • Sequential-style trigger
  • Tool-free depth-of-drive with detents
  • Removable non-marring nose tip with on-tool storage
  • Tool-free jam release and rear exhaust

Cons

  • Requires a separate air compressor, which is not included
  • No brads included โ€” the kit is the tool, a case and a manual

If you already run a compressor, $102.35 as of November 2026 buys the better-finished pneumatic โ€” about 2.6 times the WEN 61723K's price, a difference of $63.19. Both drive an 18-gauge brad, so the question is whether the finishing details are worth $63.19.

They might be. The listing publishes tool-free depth-of-drive with detents, so the setting is repeatable rather than a dial you re-find by feel; a removable non-marring nose tip with a storage spot on the tool; a tool-free jam release; a rear exhaust that points oil mist away from your face; an adjustable belt hook; and a maintenance-free motor the listing frames as keeping the motor from staining the work surface. Brads run from 5/8 in. to 2 in., and none are in the box โ€” the kit is the tool, a case and a manual.

The detail we weight most heavily is the trigger: DEWALT lists a sequential-style trigger, and that is a feature, not a limitation. According to the NIOSH and OSHA guide Nail Gun Safety: A Guide for Construction Contractors, the risk of a nail gun injury is twice as high using a multi-shot contact trigger as using a single-shot sequential trigger, and using full sequential trigger nail guns is the first of the six steps that guide recommends.

Metabo HPT NT1850DG โ€” best published runtime

Best Published RuntimeASIN B0D19V5RTY
Metabo HPT Brad Nailer, 18 Gauge Cordless, 18V Kit, NT1850DG
Metabo HPT Brad Nailer, 18 Gauge Cordless, 18V Kit, NT1850DG

Metabo HPT NT1850DG

The one gun here that publishes both a runtime and a weight: 700 nails per charge on the included 2.0Ah 18V battery, at 5.5 lbs.

Pros

  • Publishes 700 nails per charge with the included 2.0Ah 18V battery
  • Mechanical spring drive with no ramp-up time between nails
  • Tool-less depth of drive, LED work light and battery fuel gauge
  • MultiVolt compatible

Cons

  • Costs considerably more than the WEN 20512 for the same stated 2.0Ah battery capacity
  • No brads included

At $169.00 as of November 2026, the NT1850DG is the only gun here whose Amazon listing tells you both how long it runs and what it weighs: that listing publishes 700 nails per charge with the included 2.0Ah 18V battery, and 5.5 lbs.

Only one other listing here publishes a runtime figure โ€” the CRAFTSMAN at up to 420 nails per charge. Seven hundred against 420 is 280 more nails, about 1.67 times as many, roughly 67 per cent more per charge. Scope that carefully: those are the only two listings here that publish a number โ€” the WEN 20512 and Milwaukee listings publish none โ€” and the CRAFTSMAN figure is a double-asterisked listing claim, not a measurement. Likewise 5.5 lbs is the only weight published across these six listings, so there is no lightest-gun-here to crown.

The rest of the spec is the reason to want it: brads from 5/8 in. to 2 in., a mechanical spring drive which per the listing has no ramp-up time between nails, tool-less depth of drive, an LED work light, a battery fuel gauge and MultiVolt compatibility.

What it costs is $61.00 over the WEN 20512, for a battery of the same stated 2.0Ah capacity. Worth it if you nail in long sessions and resent recharging; not if you nail for twenty minutes at a time.

Milwaukee M18 FUEL Gen II โ€” premium pick

Premium PickASIN B0B9FJTDSC
Milwaukee M18 FUEL 18-Volt Lithium-Ion Brushless Cordless Gen II 18-Gauge Brad Nailer
Milwaukee M18 FUEL 18-Volt Lithium-Ion Brushless Cordless Gen II 18-Gauge Brad Nailer

Milwaukee M18 FUEL Gen II

The M18 FUEL brad nailer for people already committed to the Milwaukee platform โ€” bought on the strength of the battery system, because its Amazon listing publishes no specifications.

Pros

  • Runs on M18 batteries and chargers you may already own
  • Brushless, per its product title

Cons

  • Its Amazon listing carries no specification bullets at all โ€” no nail-length range, magazine capacity, runtime or weight
  • Highest price in this guide

At $279.00 as of November 2026 this is the most expensive tool in the guide โ€” about 7.1 times the WEN 61723K's price โ€” and there is an honest problem with recommending it. Its Amazon listing publishes no specifications at all. No nail-length range. No magazine capacity. No runtime. No weight. The only feature line on the page is boilerplate marketing copy about the brand.

What we can tell you comes from the product title: 18-gauge, M18, brushless, cordless. A $279.00 tool whose Amazon listing will not state the shortest brad it accepts is a legitimate thing to flag. Which leaves one good reason to buy it: you are already on M18, you own the batteries, and platform consistency is worth real money to you. That is respectable. It just is not a spec sheet.

Cordless or pneumatic for a brad nailer?

Pneumatic is cheaper per tool and tethered. Cordless costs more per tool and goes where you go. The compressor is the swing factor.

If you own one, the WEN 61723K at $39.16 or the DEWALT at $102.35 are the obvious buys, and you get a tool with no battery in it to degrade. If you do not, the honest comparison is $39.16 plus a compressor against $108.00 for the complete WEN 20512 โ€” and once a compressor, a hose and a fitting are in the basket, the cordless gun usually wins on total cost and on setup time. If you are weighing a compressor on its own merits, whether you need an air compressor for a nail gun is the question to settle first, because a compressor earns its keep on far more than brads.

Cordless has its own tax. Batteries add weight at the handle โ€” the Metabo listing publishes 5.5 lbs, the only weight figure across these six listings, so treat the others as unknown rather than lighter. They also run down, and only two of these four cordless listings give any figure for when. And the gun ties you to a battery family, a decision with a longer tail than the nailer.

What to look for in a brad nailer

Gauge, and why 18 is the DIY default

Eighteen-gauge sits in the middle of the trim-nailer range, and for light trim and craft work it is the gun we would own first โ€” though sources differ: This Old House calls the 16-gauge finish nailer "often considered the most versatile option" for trim, and the 18-gauge brad nailer the choice "for delicate trim work". According to Nail Gun Depot, brads are "smaller in diameter than finish nails" and "typically have less holding strength", which suits them to "light decorative trim and molding, panel installation and crafts" โ€” while "for larger trim, such as baseboards or crown molding, a finish nail is more suitable". According to Fine Homebuilding's guide to choosing trim nailers, a working trim carpenter wants 15-, 16-, 18- and 23-gauge nailers at their disposal; a DIYer buying one gun for light trim usually wants the 18. The whole argument is in the difference between a brad nailer and a finish nailer.

Nail-length range

This is where these six genuinely differ.

What each Amazon listing publishes โ€” prices as of November 2026

According to Rapid, a nailer manufacturer, the general rule is that a brad should be about three times the thickness of the material you are fastening โ€” so 1/2 in. stock points at roughly a 1-1/2 in. brad, and 3/4 in. stock at about 2-1/4 in., which is past the 2 in. maximum published by the four listings here that give a range. Check the top of a gun's published range against the thickest thing you plan to nail, and the bottom against the thinnest.

Depth of drive and jam clearing

You want to set how deep the brad sinks, and to clear a jam, without reaching for a wrench. The DEWALT publishes tool-free depth-of-drive with detents and a tool-free jam release; the Metabo tool-less depth of drive; the WEN 61723K a depth wheel and a nose latch; the CRAFTSMAN tool-free jam and stall settings. Set depth on scrap first.

Sequential or contact trigger

According to the Texas Department of Insurance's nail gun safety fact sheet, a full sequential trigger โ€” which it also calls a single-shot trigger โ€” needs both the contact tip and the trigger released and activated again before each nail, while a contact trigger fires when the tip and trigger are activated in any order. That difference is not academic: according to CDC analysis of 2001โ€“2005 emergency department data, US emergency departments treated roughly 37,000 nail-gun patients a year, about 40 per cent of them consumers rather than construction workers. According to a later study by Lipscomb and Schoenfisch using CPSC's NEISS data, the 2006โ€“2011 figure was approximately 25,000 emergency-department-treated nail-gun injuries a year.

Magazine, no-mar tip and battery platform

Two of these six listings publish a magazine capacity: 100 nails for the WEN 20512, 106 with a quick release for the WEN 61723K.

A no-mar tip is the pad that stops the nose bruising painted trim; the DEWALT publishes a removable one with a storage spot on the tool. And the four cordless guns sit on four different battery families โ€” WEN 20V Max, CRAFTSMAN V20, Metabo 18V with MultiVolt compatibility, Milwaukee M18. Owning batteries in one is a real discount; owning none makes the complete-kit guns the cheaper way in.

Frequently asked questions

Is a brad nailer worth it for DIY?

If you fasten trim by the room rather than by the board, yes. One hand holds the molding, the other fires the gun, and the brad goes in without the hammer-swing that knocks a careful miter out of line.

Do you need a compressor for a brad nailer?

Only for a pneumatic one. The WEN 61723K and the DEWALT DWFP12231 both require a separate compressor that is not included; the four cordless guns here need no compressor, hose or gas cartridge. Going pneumatic, size the compressor as in the tip above.

What size brads for baseboard?

Work from the thickness of the base. Using Rapid's three-times rule, 1/2 in. base points at roughly 1-1/2 in. brads, and 3/4 in. stock works out at about 2-1/4 in. โ€” longer than the 2 in. published maximum of the WEN 20512, the WEN 61723K, the DEWALT DWFP12231 and the Metabo NT1850DG alike, so on 3/4 in. base you are nailing at the very top of every one of those ranges. Make sure the brad reaches solid framing behind the drywall, not just the drywall.

Can a brad nailer go through hardwood?

An 18-gauge brad is a thin fastener, and thin fasteners in dense hardwood are where bent nails and blowouts show up. According to Nail Gun Depot, brads typically have less holding strength than finish nails and suit light trim and molding better than heavier work. In oak or maple, keep the brad short enough to stay inside the stock, and move to a 16-gauge finish nailer for anything that has to hold weight.

Brad nailer or finish nailer for trim?

It depends on the trim. According to Nail Gun Depot, an 18-gauge brad suits light decorative trim and molding and may leave a hole small enough not to need wood putty, while a finish nail offers more support and withdrawal resistance for larger trim such as baseboards or crown molding. Most DIYers who buy one gun buy the brad nailer first.

Which one we would buy

The WEN 20512 at $108.00. It is the only gun here that is finished being bought the moment you buy it: battery, charger, 400 brads, a published 3/4 in. to 2 in. range, a 100-nail magazine, no compressor and no second trip to the checkout. For a DIYer who owns neither air nor a battery platform, that is the whole argument.

Everything else is conditional. Own a compressor and want the better tool? The DEWALT DWFP12231 at $102.35, for its detented depth setting and sequential-style trigger. Own a compressor and want to spend the least? The WEN 61723K at $39.16, with 2,000 brads and the shortest published minimum here. On CRAFTSMAN V20? The bare-tool CMCN618B at $99.00. Nail in long sessions? The Metabo HPT NT1850DG and its published 700 nails per charge. On M18, buying the platform rather than the spec sheet? The Milwaukee.

Whichever you pick, 18 gauge solves one slice of the fastening problem. For where it sits next to framing nailers, finish nailers and staplers, read our nail gun buying guide.

About the Author

Photo of Cheryl Thompson
Field tester

Cheryl Thompson

Cheryl Thompson is the tools editor at The DIY Tool Review. A lifelong fixer and self-confessed tool addict, she has spent years buying, borrowing and wearing out hand and power tools across home renovation, furniture building and everyday repairs. She writes hands-on, no-nonsense reviews to help fellow DIYers spend their money on the tools that actually last.

Read next

3 files